Welcome to Large Scale Modeller: The home of the large scale military model builder.
Search the Community
Showing results for tags 'rule'.
Found 2 results
Scribing Ruler 15cm/6in RB Productions Catalogue # RB-T049 Available from RB Productions for €4,50 Sometimes, it’s the simplest of tools that we get the most workbench satisfaction from. This tool is one of those that will probably be on your bench quite a lot due to its multirole purpose in aiding the marking/scribing/measuring of various aspects of your model’s surface. Packed into a slim, clear wallet, the Scribing Ruler is carefully taped to a card stiffener which protects it from bending and rolling around loosely. The rule itself is manufactured from very thin stainless steel and is already presented without the need to remove any fret, although I do suggest carefully removing the fret connection tabs from each end of the rule. A small jeweller’s file should easily do this. One edge of the rule is calibrated in metric divisions, whilst the opposite is measured imperially. For the metric, small holes are provided at every 1mm point, with pointers etched to show full centimetres and also 0.5mm positions. For the latter, you would need to gauge the position between two adjacent points. For the imperial side, holes are provided every 1/24 of an inch, with etched positions identifying every 1/12 and 1/48 of an inch. For the latter, again you will need to gauge this from adjacent hole positions. With this tool, you can of course wrap it around the surface of a model due to the very thin gauge of the stainless steel, and after marking the start and finish positions of your line to scribe, you can then use the straight edge to run a scriber along, providing a sharp, clear guide as you go, in the same way that some modellers would use plastic Dymo tape. Of course, you can just use the edge for casual scribing or marking your surface with a pencil, or just mark relative positions using the holes. The holes themselves are quite small and ideally you would need a very sharp pencil to be able to use the tool properly, but hey, that’s accuracy! Conclusion A simple, yet very nicely executed and manufactured tool which I don’t doubt will be immensely useful to the average modeller who likes to add rivet lines or scratch details to their models. My sincere thanks to RB Productions for the review sample seen here. To purchase directly, click the link at the top of this article.
Aluminium Alloy Scale DSPIAE Catalogue # AT-AS Available from Breveco Modelling for 16,50€ For the last of my current batch of reviews of DSPIAE tools, we look at their new Aluminium Alloy Scale, or in simple parlance, ‘scale rule’. Scale rules have all sort of incredibly useful applications in any part of our hobby where we are looking at measuring things in particular scale quantities. The new DSPIAE tool is packaged into a robust cardboard tube with an end-opening cap. Gone is the Aztec-style décor here, but the all-black tube does have a little décor that shows the end profile of the scale rule, plus the scales listed that it is marked in. These are 1/144, 1/100, 1/72, 1/48, 1/35 and 1/24. Opening the tube up and sliding out the end cap reveals the familiar red anodising of the DSPIAE range, with the star-like profile of the rule inserted into a foam block within the cap to protect it. An identical foam block protects the opposite end of the rule, down within the tube. The rule itself measures 32cm and has a good weight to it that should make its use a breeze. If it was too light, I’d perhaps find it a little nondescript, but this has a good weighty feel that is reassuring. Also of note is that each scale isn’t printed right up to the edge, which is good in case you were to accidentally damage the end of the rule. DSPIAE has also removed the corners from the rule, so you won’t cut or stab yourself! This rule has been designed with that profile so as to accommodate the six scales mentioned above, and these are neatly printed on these in fine white lines with the accompanying scale easy to note. Each scale is broken down into 1 metre equivalences, with each metre again subdivided into 10 parts (10cm equivalences). In some cases, this is split down even further. Conclusion Another excellent tool that is superbly engineered and beautifully made. If I had only one question, it would be the lack of the popular 1/32 scale. Maybe this should have replaced 1/100 or 1/24. However, if you are in the market for a scale rule that is catered for by that this product offers, then I doubt you’d fine anything as good as this. My sincere thanks to Breveco Modelling for supplying the review sample seen here. To purchase directly, click the link at the top of the article.