Search the Community
Showing results for tags 'tool'.
Scribing Ruler 15cm/6in RB Productions Catalogue # RB-T049 Available from RB Productions for €4,50 Sometimes, it’s the simplest of tools that we get the most workbench satisfaction from. This tool is one of those that will probably be on your bench quite a lot due to its multirole purpose in aiding the marking/scribing/measuring of various aspects of your model’s surface. Packed into a slim, clear wallet, the Scribing Ruler is carefully taped to a card stiffener which protects it from bending and rolling around loosely. The rule itself is manufactured from very thin stainless steel and is already presented without the need to remove any fret, although I do suggest carefully removing the fret connection tabs from each end of the rule. A small jeweller’s file should easily do this. One edge of the rule is calibrated in metric divisions, whilst the opposite is measured imperially. For the metric, small holes are provided at every 1mm point, with pointers etched to show full centimetres and also 0.5mm positions. For the latter, you would need to gauge the position between two adjacent points. For the imperial side, holes are provided every 1/24 of an inch, with etched positions identifying every 1/12 and 1/48 of an inch. For the latter, again you will need to gauge this from adjacent hole positions. With this tool, you can of course wrap it around the surface of a model due to the very thin gauge of the stainless steel, and after marking the start and finish positions of your line to scribe, you can then use the straight edge to run a scriber along, providing a sharp, clear guide as you go, in the same way that some modellers would use plastic Dymo tape. Of course, you can just use the edge for casual scribing or marking your surface with a pencil, or just mark relative positions using the holes. The holes themselves are quite small and ideally you would need a very sharp pencil to be able to use the tool properly, but hey, that’s accuracy! Conclusion A simple, yet very nicely executed and manufactured tool which I don’t doubt will be immensely useful to the average modeller who likes to add rivet lines or scratch details to their models. My sincere thanks to RB Productions for the review sample seen here. To purchase directly, click the link at the top of this article.
Planet Working Bench Amati Catalogue # 7396 Available from Cornwall Model Boats for £10.58 Having worked in plastic modelling for a while now, where I’m having to remove casting blocks from larger components but doing that either on my cutting mat or between my fingers, a tool like this appears to be very useful. When it comes to ship modelling too, the ability to be able to lay some small timber sheet flat whilst you use a fine saw on smaller components, without sawing tracts into your worktop (ask me how I know!), definitely helps. Amati’s Planet Working Bench is a tool that is designed for work on small components and materials, helping you hold items whilst you saw, file and drill. Let’s take a closer look. Amati’s Planet tool is packed into an attractive, sturdy and glossy box with an image of the tool clamped to a desktop. The back of the box is a little more illustrative, with examples of how this tool can be used with your work. All writing is in Italian, but we can grasp what’s happening fairly easily. Although Amati are generally known for their wooden model ships etc. this tool can of course be used for other areas of modelling where basic tools such as saws, files, and drills, are used. Inside the box, two thick plastic sleeves contain the components. In the largest is the Planet Working Bench itself, complete with two small aluminium bollards plugged into it. These bollards have a rubber O-ring fitted to them to prevent the metal scuffing any delicate work that you will use with the tool. The main part is moulded from a very tough plastic that still does have a little give in it, but it certainly rigid enough for the tasks that it’s designed for. It also has various channels moulded within in as well as holes to reposition the bollards, and a series of small, numbered holes which I’ll come back to very soon. The front slot is there to help you cut into materials, without a risk of cutting into your actual workbench. Just be careful not to start sawing into the Planet itself. The second wallet contains the two clamps which will secure the Planet to the desk. These are formed from two angled, threaded rods onto which a locking nut and the part which forms the lower side of the clamping jaw. To fit these to the Planet, you insert them from the underside and lay the angled part of the metal rod in the moulded channels. Slacken the nut off and then fit to the edge of your workbench, securely tightening the nuts to lock everything in place. Now, those small numbered holes. These refer to a moulded sleeve in the underside of the Planet, into which you will fit a wooden dowel or metal rod into which you wish to drill a hole centrally within the diameter. The hole of course aligns with the dead centre of the sleeve into which you will plug the wood or metal rod. Conclusion This is a very handy little gadget for working on those small model parts, but sold as it is, the full potential of the tool isn’t realised. To really get your money’s worth from it, I really do advise that you also purchase the small clamps which are designed to plug into it. These is called the ‘hand vice’ on Amati’s catalogue page and contains one single unit. Better still, a couple of these would be immensely useful. The Planet itself is very reasonably prices, nicely constructed and is a cinch to fit to your bench. I’ve already started to use it whilst building my Amati Orient Express Sleeping Car. My sincere thanks to Amati for sending this tool out for review. To purchase directly, click the link at the top of this article.
Craft Tools Rack DSPIAE Catalogue # AT-R Available from Breveco Modelling for €44,50 My workbench is always a clutter, despite it being fitted with a whole array of HobbyZone modules that store paint, brushes, tools etc. As modellers, we always tend to pull the same small number of key tools and things back to our bench as soon as we start work on our next project, or after a well-needed mid-project tidy. I’d been after a small tool rack so that I could keep just a few regular bits and pieces together. My good friends at Breveco Modelling told me that they had such an item in stock, from DSPIAE. This is the same company whose Stepless Adjustment Circular Cutter and Single Blade Nipper, that I recently reviewed here on Large Scale Modeller. As luck would have it, Breveco were visiting Scale Model World 2017 at Telford, so I took the opportunity to pick one up from them in person. Now, this is no flimsy or lightweight box. This little package is actually quite heavy, and the box is built to withstand a nuclear blast, or so it would seem. The same high-quality presentation has gone into this product as it did with the others. Box art is a little unusual from the lid, with only a small number of words, and a side drawing of the rack is present. The box sides do give a little more away, with photos and some explanation of the product itself. The extremely robust lid took some effort to remove from the tray, such is the airtight fit of this. Underneath this lies a removable panel which shows the various parts within, and instructions on assembly of the tools rack (not that it’s too difficult to fathom yourself!). Lifting out the foam backed panel reveals a precisely cut foam block into which the various components are inserted, and each is named, just in case you had become confused at some point. All along, there’s no doubt at the level of quality that DSPIAE has employed here, but does that carry over onto the tool rack itself? Well, the answer is a resounding YES! Each part is now lifted carefully from the box, including a small wallet with a number of screws, sticky feet and a hex-key. All of the main components of the rack have a super smooth finish and a red-anodising to them, creating a striking appearance. For an extra touch, the outer edges of the main rack are bevelled, removing the anodising, and allowing the shine of the aluminium to come through. Assembly is very straightforward. I start by taking the baffle plate, and slotting this inside the rear part of the main rack. Two knurled screws now hold this in place from the rear of the rack, with two plastic washers to protect the red anodised finish of the parts. This baffle can be moved up and down within the stand, due to the slotted nature of the fixing point. This can be suited to fit your own particular tools. The two large openings in the front part of the rack now need to be tackled. A tool tray (bottom case) slots into the open side of the rack, and this is secured from underneath with three countersunk screws, tightened with the hex-key. Whilst I’m at this point, I also peel off the 3M sticky rubber feet and add these to the underside so that the rack isn’t scratched by any workbench debris. I am pretty fussy about things like that, and want to maintain something in the best way possible, for as long as humanly possible. Lastly, there is an optional module which can fit into the smaller of the two tray areas (well, it’s designed for the smaller, but will fit the larger area if you wish), and this is the modularised slot block. This is designed to fit brushes etc. What I like about the areas at the front is that the larger one fits a bottle of Tamiya Extra Thin Cement perfectly, so you won’t knock it over on your bench and melt your work in the process. Conclusion I’ve already got this stuffed with all manner of tools that I want to keep close at hand, including my razor saw, small brushes, sprue cutters etc. This takes the desk-tidy idea a step further and makes it both flexible and elegant. The weight of it, plus the rubber feet, means that it won’t skirt and slip around your bench accidentally. It firmly stays put, which is also useful if you store your cement bottle in there too. Putting the lid back on and screwing tight whilst in the stand, is straightforward. This is a quality tool, and that is reflected in the price, which I still think is very, very reasonable for a chunk of heavy, precisely machined metal and the other included parts. These aren’t something which I tend to see every day, but I’m sure if you drop Evert or Corien a message at Breveco Modelling, they’ll be able to sort out your requirements. My sincere thanks to Breveco Modelling for the sample seen here. This item isn’t yet on the website, but please contact them to register your interest.