Jump to content

What is on your bench right now ? Share a picture :)


Recommended Posts

Looking good Carl, are you painting it out before reinstalling? One idea, if you put ceiling board to the beams, you could have adjustable LED spots recessed in it. Another trick we use in interiors is a wall / ceiling edge cove light. Could light this with a string of LED’s again…just a thought……

  • Like 4
  • Thanks 1
Link to post
Share on other sites

Thanks Phil & Harv! I'm going to leave it as is. The rest of the basement isn't finished either. In fact, only two walls have drywall on them. The worklights are quite a bit brighter than what I had before so pot lights would be over kill. 

I will probably paint the floor where the new concrete was poured though. 

  • Like 4
Link to post
Share on other sites

I was wondering about the floor situation, to have it uneven will create risk of loosing tiny bits in nooks and crannies. Few bags of levelling compound would clean it up nicely. I wish I lived closer to help.  

  • Like 3
  • Thanks 1
Link to post
Share on other sites
21 minutes ago, Martinnfb said:

I was wondering about the floor situation, to have it uneven will create risk of loosing tiny bits in nooks and crannies. Few bags of levelling compound would clean it up nicely. I wish I lived closer to help.  

Martin, I've got a bag of ready mix for that very reason. Just wanted to start getting things out of the way first as we also have to move our oldest into his own room. Some of it will go into the space I recently vacated. 

  • Like 5
Link to post
Share on other sites

Got the bench cut and fitted today. 

Went easier than I hoped. I was half worried I'd get the angles wrong and it would be either too big or small. 

PXL_20210606_191356560.thumb.jpg.693d762c0ea2f3ed0e82431b6388d54c.jpg

I used a strip of 2x3' mounted to the wall as a support. They're anchored to the 2x4s behind the drywall

PXL_20210606_173324801.thumb.jpg.0b28f3507b5cb811c0aef8b5dd783977.jpg

  • Like 8
Link to post
Share on other sites
On 6/4/2021 at 9:59 PM, BlrwestSiR said:

Thanks Peter! The best part is the space was all previously boarded up so it's a bonus and lets us organize the rest of the basement better. 

I went ahead and worked on getting some of the drywall up tonight. 

PXL_20210605_023313027.thumb.jpg.c79f05f4b30466bb5c3aa9de89ebbf46.jpg

There's just one piece left but it'll be the most challenging as I have to measure and cut out the spot for the switch and outlet. 

With the corner done, I hung the lights up as well.

At this point, I put the bench back together. It just fit in the space. I've got a 1/2" on either side. :thumbsup2:

PXL_20210605_024202803.thumb.jpg.0cd45b5d8d158f290d90c24a7be22bf4.jpg

PXL_20210605_024152731.thumb.jpg.5326155eae386c803612f07e7dd9b601.jpg

With my Arttystation back in place. 

PXL_20210605_025741886.thumb.jpg.c7d9547b80bd0862aa64923600f8699a.jpg

The rack of paints on the right side are the ones my boys use so those will now be on the bench instead of on the floor beside it. 

It's finally coming together.

Carl

Nice layout whatever you do not go cheap on lighting LED was not around when I did mine but they are going to be fitted in the workshop and the office/hobby room.:unworthy:

  • Like 4
  • Thanks 1
Link to post
Share on other sites

The painting and weathering is mostly finished and will be sealed with a matte coat after adding the engine. After gloss coating the decals, I brush chipped with different grey/blue tones and some more with interior green as primer color. 
Then it was time for oil colors heavy diluted with thinner, first in blue and then in a color similar to interior green, which were spreaded and partly removed with a saw brush and some thinner. For effect, I used different brushes with the oil thinner mix and dabbed carefully to break the uniform appearance of the panels.

Cheers Rob

IMG_8829.thumb.JPG.f832e5292f4dc749c3ce38e05fdda206.JPG

IMG_8830.thumb.JPG.75871e1a19613354461acde2c14dba85.JPG

IMG_8831.thumb.JPG.6e85c9a5d8327ea0935f2dcf5c981616.JPG

  • Like 10
Link to post
Share on other sites
42 minutes ago, DocRob said:

The painting and weathering is mostly finished and will be sealed with a matte coat after adding the engine. After gloss coating the decals, I brush chipped with different grey/blue tones and some more with interior green as primer color. 
Then it was time for oil colors heavy diluted with thinner, first in blue and then in a color similar to interior green, which were spreaded and partly removed with a saw brush and some thinner. For effect, I used different brushes with the oil thinner mix and dabbed carefully to break the uniform appearance of the panels.

Cheers Rob

IMG_8829.thumb.JPG.f832e5292f4dc749c3ce38e05fdda206.JPG

IMG_8830.thumb.JPG.75871e1a19613354461acde2c14dba85.JPG

IMG_8831.thumb.JPG.6e85c9a5d8327ea0935f2dcf5c981616.JPG

Rob,

   The oils have added some great variation to the skin of the machine.  Well done!

  • Like 5
  • Thanks 1
Link to post
Share on other sites

I can see the finish line now with the Hellcat. I installed the Brassin engine and exhausts, which was a bit fiddly and needed some grinding on the engine mount, not so cool after painting.

IMG_8833.thumb.JPG.37afa7ec17df8bc815c9d470a9817b4f.JPG

Finally the H-cat received a coat of matte varnish, after I finished some detail painting and repairs. On the pics, I found some other spots for rework.

IMG_8835.thumb.JPG.de365d997c159141a66435c23b8eca37.JPG

IMG_8837.thumb.JPG.fe202db2a63cd2a9d7b9ce21e746df2c.JPG

IMG_8838.thumb.JPG.4f874973a271a07210be90e9d14f491b.JPG

Cheers Rob

  • Like 11
Link to post
Share on other sites
22 hours ago, DocRob said:

I can see the finish line now with the Hellcat. I installed the Brassin engine and exhausts, which was a bit fiddly and needed some grinding on the engine mount, not so cool after painting

Stunning Rob, the weathering and colour modulation is superb….

  • Like 2
Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    No registered users viewing this page.

×
×
  • Create New...