Trumpeter Titanic 1/200

[Winnie]

This is a multi year project, I have started threads in a few maritime forums, but thought I'd make one here too. This is the progress made THIS month!

So got a tiny bit completed on B deck, not much to do, 2nd class restaurant and a couple promenades. and the deck below the bridge. had to work to get the deck to fit, minor surgery. Also fitted the PE sheets for the rails on the outside bulkhead, but only the back plate, the spars will have to happen AFTER the decs are inserted. Pictures are bad, because  I was in a rush...

 

 

 

Waterways still need a dash of black there! and the ladders came off the rear bulkhead, those will be reattached shortly, with the last deck equipment needed.

 

Shapeways bridgefront there.

The doors seem very red, they look more brown in real life. 

Holes are drilled for portholes, and I have fiberoptic, but I'm questioning my plan to light it. we'll see, once I finish the hull, I'll have to make my mind up...

Cheers!

 

[FullArmor]

Nice to see ship building here too🙂. Variety for tanks and planes.

[DocRob]

Like FA said, it´s good to see some nice ship building here. I will follow and am eager to see more.

Cheers Rob 

[Winnie]

I'll post more shortly, I'm already well on the way on 'A' deck, just a few (A LOT) of windows to do...

[Winnie]

I'll try to add a few pictures!

A Deck, deck veneers laid down, waterways and expansion joints laid down. I've been using white glue for all of it. It's flexible enough to allow for temperature differences, and seem to hold the PE better than CA glue... 

She's a big lady!

Still have to finish the hull plating at the stern, I will try with the metal plates again, but if that fails, I can add in the plastic plates from Midwest Model Shop.

 

Cheers

H.

 

[DocRob]

Beautiful looking decks, H. I wonder about the CA though. For the decks white glue might be a god option, but for small PE parts? I think the white glue can´t take any strains. I use Colle 21 CA by the gallon for my metal MFH kits and used it with ships PE as well with no complaints.

Cheers Rob

[Count0]

5 hours ago, DocRob said:

I use Colle 21 CA by the gallon

Super glue will soak the wood, ruining it for staining later, and the parts won't stick anyway. At least that's what I have found. Epoxy would be my choice, applied very sparingly. It going to ruin the wood as well, if you miss. So some kind of guide would be a good idea. Like tape.

[Count0]

I know one of the modern Titanic kits was rumored to have a misshapen bow? Is it this kit? if yes, any plan to correct that?

[DocRob]

51 minutes ago, Count0 said:

Super glue will soak the wood, ruining it for staining later, and the parts won't stick anyway. At least that's what I have found. Epoxy would be my choice, applied very sparingly. It going to ruin the wood as well, if you miss. So some kind of guide would be a good idea. Like tape.

H. Spoke about CA gluing PE parts, that was what I was referring to. 
I double planked a complete wooden sailing boat, using CA. I know, wooden ship modelers often dislike CA and you have to be really careful using it, to not stain the visible side, but it works good and superfast.

This is the hull, I made, there are no stains, even after finishing the wood with varnish. The golden ornate PE is also glued on with CA.



Cheers Rob

[Winnie]

1 hour ago, Count0 said:

I know one of the modern Titanic kits was rumored to have a misshapen bow? Is it this kit? if yes, any plan to correct that?

I think that's the wooden ship, Occre or some such.

I won't be doing any massive surgeries, I have a couple of Shapeways parts, like the B deck front bulkhead, that looks more correct. 

 

@DocRob I'm not using wood glue to glue PE to PE, only PE to plastic, a couple of the bulwarks had some tension due to the etching, and they are holding with wood glue, but not with CA for some reason. That was the problem with the hull-plates as well, the plates held for a bit then one edge would peel... pain in the canugies...

The waterways, and expansion joints are flat pieces on flat decks with no strain, and they're holding down great with white glue. And it's easy to position, and they're flexible ish after setting, so that they shouldn't pop off...

Your wooden ship is magnificent though...

[DocRob]

15 minutes ago, Winnie said:

Your wooden ship is magnificent though...

Thank you, it is my first wooden ship and went rather quickly and fine, but I stalled with rigging until now. I will definitely finish the Duchess of Kingston soon.

Cheers Rob