Jump to content
Playing in the Sandbox Group Build Sept 1, 2024 - Jn 1, 2025

Macchi M-5


Recommended Posts

  • Administrators
On 1/13/2020 at 2:58 PM, sandbagger said:

Hi all,
Pilot's seat modified:

Thickness of seat back reduced.
Seat belt slots added.
Seat back rolled edge added (0.4 mm lead wire.

Mike

seatrollover.jpg

Mike, I love your approach on this.

Like yourself, I find some kind of odd masochistic pleasure in pleasure in HPH kits as they provide us with subjects nobody else dares tackle in 1/32 "The One True Scale".  :)

Personal;ly,. I would probably have hauled out the Evergreen sheet and started drilling, but in retrspect, I think you made the right move here.

I have this kit sitting in my stash somewhere, but before I tackle it, the HPH B-36, Fisher's Guppy Skyraider, and Fisher's September Fury need to be finished. 

I'm wondering if I need to build the Aviattic Balilla first to get me in the frame of mind to tackle this one. When I see a builder like you scratching your head on a build, even if it is HPH, warning klaxons go off in my mind and I stop and take immediate notice.

hahahaha

  • Like 5
Link to comment
Share on other sites

Hi all,
I'm calling the fuselage finished.
I've scuffed the underside roundel to represent water wear.
The fuselage was given a weathering coat of Dark Dirt clay wash 'Flory Models' to represent general grime, especially as crew and mechanics had to walk on the cockpit decking.
It was then sealed with 'Alclad' Light Sheen (ALC-311) lacquer.
A second light wash of White was applied to give an indication of salt spray and to highlight the fuselage panel nail lines, then sealed again.

Now onto the wings,

Mike

fusdone1.jpg

fusdone2.jpg

fusdone3.jpg

fusdone4.jpg

fusdone5.jpg

fusdone6.jpg

  • Like 8
  • Thanks 1
Link to comment
Share on other sites

Hi all,
The propeller is finished.
Hand made wood laminate special from 'ProperPlane'.
Airbrushed with 'Alclad' Light Sheen (ALC-311) with a few drops'Tamiya' Hull Red (XF9).
Erosion protection stripes (either Copper, Tin or Mondel (Copper-Nickel Alloy) brush painted.
Propeller bosses brush painted with 'Mr. Colour' Stainless Steel (213).
Final sealing coat of 'Tamiya' Clear Orange (X26).
Propeller bosses coated with 'AK Interactive' Kersosene (AK2039).

Mike

propdone.jpg

  • Like 6
  • Thanks 1
Link to comment
Share on other sites

Hi all,
I've started working on the wings.
The wings were covered in Clear Doped Linen (CDL), but of a much lighter, almost white' finish.
Photographs of the aircraft show darker ribs tapes over the lighter covering, which I'm assuming was because the rib tapes were effectively double thickness linen.

ribbing.jpg

The wing were primed with 'AK interactive' white AK-759.
The wing spars were masked off and airbrushed with thinned 'Tamiya' Smoke (X19).
The masking was removed and the internal cross bracing wires drawn on with a pencil.
Pre-shading was then airbrushed with thinned 'Tamiya' Smoke (X19).

wing1.jpg

The wing was lightly airbrushed with the white primer to tone down the pre-shading and spars.

wing2.jpg 

The raised detail was then lightly sanded to highlight the wing ribs and outer edges.
The whole wing was then sealed with 'Alclad' Aqua Gloss (ALC-600).

wing3.jpg

'Aviattic' clear Bleached CDL (ATT32044) was used to cover the wing.
The same decal, cut into 2 mm strips was used to cover the rib tapes.

wing4.jpg

This is a long tedious job as both sides of the upper and lower wing need to be treated this way, but hopefully it'll have the desired effect.
I still have the roundels and markings to apply, plus any final weathering and a sealing coat of semi-matte to finish.

Mike 

  • Like 4
  • Thanks 1
Link to comment
Share on other sites

Thanks Sir Des, if a tad overstated :)

Hi all,
I think that's as far as I can take the top roundels.
The inner white ring was replaced with the same 'Aviattic' CDL decal used to cover the wing.
The reason being that photographs show what appears to be CDL inner roundel rings, not painted white.
Moving on now to the undersides of both wings.
That means red and green outer areas with CDL centre sections and 'ghost' roundels' under the upper wing.

Mike

toproundels2.jpg

  • Like 7
Link to comment
Share on other sites

Hi all,
The wings and tail plane/elevators are finished.
The underside of the upper wing has 'ghost' roundels visible from the roundels on the top surface - created with masks and airbrushed..
The heat deflector panel (for engine exhausts) on the inboard left wing painted with 'Alclad' Steel on black primer.
Final weathering applied using 'Flory' fine clay wash.
Surface finish airbrushed with 'Alclad' Light Sheen,

Mike

wingdone1.jpg

wingdone2.jpg

wingdone6.jpg

wingdone3.jpg

wingdone4.jpg

wingdone5.jpg

  • Like 5
  • Thanks 1
Link to comment
Share on other sites

Hi all,
The fin and rudder are now finished.
The kit decals were not used, but instead airbrushed.
The CDL covering and rib tapes were applied as for the wings.
'Flory Models' fine clay wash (Dark Dirt) applied for weathering.

Mike

finruddone.jpg

  • Like 5
  • Thanks 1
Link to comment
Share on other sites

Great attention to the detail concerning used materials in reality and the concerning effects reproduce them.

14 hours ago, GusMac said:

Those 'ghost' roundels are great. A really neat touch that just enhances the realism. :unworthy:

I second that, what a great fake translucency.

Cheers Rob 

  • Like 2
Link to comment
Share on other sites

Hi all,
And the lower wing floats.
The kit supplies the earlier 'hull' shaped wing floats. which were attached directly to the underside of the lower wing.
Also supplied are the later 'ski' type wing floats, which were attached to the underside of the lower wing with support struts.
Once again no surprise that the kit does not supply the support struts, just the floats!!

I made the support struts from soldered micro-tube and chiselled recesses into the underside of the lower wing so the floats are correctly positioned, taking into account the 3 degrees of wing dihedral angle.
Some Macchi M.5 aircraft had wing floats of just varnished wood, others had markings such as Italian roundels, white discs etc.
This particular Macchi M.5 had the Italian tricolours applied, similar to that of the fin.  

Mike

floats3.jpg

floats7.jpg

  • Like 6
  • Thanks 1
Link to comment
Share on other sites

Hi all,
After finishing the wing floats it was pointed out the they seemed too short.
After re-checking the drawing I realised that in fact they should span the chord of the lower wings and also that the sides of each float were angled in towards the nose.
So back to the drawing board.
As the micro-tube struts were already fitted and matched the location recesses I'd created in the wing, I didn't want to start the floats from scratch.
Also, because of the struts, I couldn't really cut and insert an extension to lengthen the floats.
So I stepped the top and bottom surfaces and added 0.5 mm thick plastic card strips.
The bottom of the floats had a packing piece of 0.5 mm thick plastic card to help create the shallow curve on that surface.
Once that was done I filled the sides with modelling putty and once set, sanded it all to shape.

So not perfect, but I think close to the correct size etc.
The second shot shows the floats test fitted to the underside of the lower wing halves,

Mike

floats72.jpg

floats9.jpg

  • Like 5
  • Thanks 1
Link to comment
Share on other sites

Hi all,
The upper wing has now been joined and the lower wings secured to the fuselage (with the required 3 degrees of dihedral angle)
The shots below show the upper wing dry fitted with only the unfinished 'V' interplane struts located.
The unfinished engine is just positioned onto the fuselage 'Z' support struts.

The two upper 'Z' struts from the engine bearers to the underside of the upper wing still need to be drilled into the bearers and upper wing.
NOTE: The unfinished engine is positioned further rearwards than it will be when finally fitted.

So far both wings appear to be correctly aligned when viewed from the top and sides.

Mike

testfit1.jpg

testfit2.jpg

testfit3.jpg

  • Like 2
  • Thanks 1
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...